Formlabs Form Wash (2nd Generation)
FormLabs

Formlabs Form Wash (2nd Generation).

SKU FH-WA-02
Price on application

Automatically cleans resin 3D printed parts, thoroughly and efficiently, with IPA or alternative solvents.

This one's priced per practice. Tell us what you're setting up and a person will come back with a real number, fast.

Formlabs Form Wash (2nd Generation)

Set the time,let it wash.

All SLA 3D printed parts need washing to remove residual resin. Form Wash cleans them automatically with IPA or alternative solvents, straight on the build platform or in the wash basket, then lifts them out of the solvent to air dry.

10 min
Default wash time in fresh IPA
7 to 15 L
Solvent volume, to suit the size of the job
3
Mount heights, for prints up to 70, 120 or 185 mm tall
4
Wash presets, 1 to 20 minutes, or a custom time
Solvent swirling around a build platform submerged in Form Wash

On the platform or in the basket

Keep parts on the build platform as you move them from the printer to Form Wash, or take them off and place them in the wash basket. An impeller agitates them in solvent for the time you set, and when washing completes, Form Wash raises them out of the solvent so they can air dry.

  • A magnetically coupled impeller, with high and low speeds
  • The inner lid contains the solvent while parts are lowered and raised
Form Wash on a lab bench with dental models on the build platform at the solvent line

Adaptable to build platforms

Adjustable platform mounts, configurable at various heights and widths, let you switch between build platforms. Tailor the solvent volume to the size and quantity of your parts, and use less solvent for smaller parts and builds.

  • Three mount heights, for prints up to 70, 120 or 185 mm tall
  • The outer mounts take Form 4 and Form 4B build platforms
  • Fill to 7, 10 or 14 L to match the mount height
Formlabs Form Wash with three dental arches on the build platform above the wash basket

Your choice of solvent

Formlabs recommends IPA for the best cleaning performance, and alternative solvents such as TPM and Formlabs Resin Washing Solution are also compatible with Form Wash.

  • A hydrometer is included, to measure the resin concentration of your IPA
  • Set the time and start, pause or end a wash with the display and knob
  • Default, Quick, Short and Long presets of 10, 1, 5 and 20 minutes
A dental lab bench with a Form 4B, a Form Wash with its build platform of models raised, and a Form Cure curing models

Between the printer and the cure

Form Wash is part of a 3D printing ecosystem that is easy to learn and use. Formlabs pairs it with Form 4B to print and Form Cure to post-cure.

The workflow

Scan, design, print, wash, cure.

Every case runs through the same five steps. Here is where the Form Wash sits, and the Formlabs units it works with.

  1. 01 · Scan
    Intraoral scanner

    Capture the case digitally, chairside.

    See scanners
  2. 03 · Print
    Formlabs Form 4B

    Formlabs' masked SLA 3D printer for dentistry.

    See it
  3. 05 · Cure
    Formlabs Form Cure

    Heat and 405 nm light, with validated presets for Formlabs resins.

    See it

Specifications

Washing
Magnetically coupled impeller; parts raised out of the solvent to air dry
Printers
Form 4, Form 4B, Form 3/+, Form 3B/+, Form 2
Solvents
IPA (recommended), TPM, Formlabs Resin Washing Solution
Solvent volume
7 to 15 L
Maximum part size
20 x 14.5 x 19.5 cm
Controls
Display and knob; 1, 5, 10 and 20 minute presets or a custom time
Included
Wash bucket, wash basket, hydrometer, 2 platform mounts
Power
90 to 240 V, 50/60 Hz, 50 W
Operating temperature
18 to 28°C
Size (W x D x H)
31.5 x 29.3 x 40.5 cm; 71.4 cm tall with the lid open
Access space (W x D x H)
40 x 40 x 80 cm
Weight
8.6 kg without solvent

Questions

Which printers is it for?

Form 4B and Formlabs' other desktop printers: Formlabs lists Form 4, Form 4B, Form 3/+, Form 3B/+ and Form 2. For Form 4BL builds, Formlabs pairs Form Wash L.

How long does a wash take?

Formlabs' default is 10 minutes in fresh IPA, and its settings give 5 minutes for Precision Model and Fast Model Resin. After an IPA wash, let parts dry for at least 30 minutes.

Can I wash biocompatible parts in it?

Follow the washing notes in the resin's Manufacturing Guide. Formlabs also says to keep a separate wash bucket for resins used in biocompatible applications.

Who installs and supports it?

Andarsyn. We install it at your practice or lab, set it up and walk your team through the first print before we leave, and a person answers the phone after.

Product information and images: Formlabs. Sold, installed and supported in Australia by Andarsyn.

Next step

Talk to us about the Form Wash.

We install it alongside your printer and walk your team through the first wash. Tell us what you're setting up and a person will come back with a quote.